JUICE's 600whp Drag Hatch Project **New Pics/Vids pg.57/58**

Post YOUR Hatchback here
 Reply
User avatar

By JUICE
- Wed Jan 16, 2013 10:03 pm #324263 Picked up a scatter shield and a p28 this week. I'm down to turbo, Neptune RTP and an ATI damper and I'll be ready to go. My buddy is about to have his $$$$ together for my current setup, which will really get the ball rolling.

Can't wait to hear the monster LS/Vtec fire up again!!! :twisted:
User avatar

By JUICE
- Fri Jan 25, 2013 11:50 pm #324992 Sold the LS/Evo 8 setup yesterday.. Was hard to see it go. Went to a really good friend though, excited to see what he'll run with it.


Got my turbo on the way, its a precision SC6162 cast wheel with a garrett 4" anti-surge housing put together by pureturbos.com. It was only used for a few dyno pulls, got a hell of a deal on it thru a friend of a close friend :lol:

Image

Image

Image

Image
User avatar

By 92egdxhatch
- Sun Jan 27, 2013 7:53 pm #325056 Very nice.

Can't wait to see some numbers!
User avatar

By Uknterror
- Mon Jan 28, 2013 3:06 am #325072 fuuuuuuuuuuuh so much madness!
User avatar

By Punksz6
- Mon Jan 28, 2013 7:12 pm #325112 :thumb:
User avatar

By JUICE
- Mon Jan 28, 2013 11:41 pm #325143 Thanks fellas!

Picking up my ATI damper tomorrow and got an appointment for Wednesday with my tuner to get my Neptune RTP and a basemap installed on my p28. If all goes as planned, motor should be in and running by this weekend. I need to get it in so I can start on intercooler piping and find out what I'm gonna have to do to make the exhaust work.
User avatar

By kylenjdm93
- Thu Jan 31, 2013 1:29 am #325278 suggestion>>>> polish the valve cover bro :thumb:
User avatar

By JUICE
- Thu Jan 31, 2013 3:22 am #325286 Just wanted to leave that one on till I got the motor in. I've learned my lesson with crispy valve covers and chains hoisting the motor in and out. :lol:


Gonna look for one in better shape, have some AN fittings welded on, then decide on a color. :thumb:
Last edited by JUICE on Fri Feb 01, 2013 2:03 am, edited 1 time in total.
User avatar

By kylenjdm93
- Thu Jan 31, 2013 4:57 am #325290 when you do your oil catch can make sure you purchase a good one, the lines should be same height as the valve cover, unless the baffles inside are chambered differently to allocate the pressures differently :thumb:

many people buy cheap ones and never buy them again due to the poor quality, not all catch cans are the same.

figured I would throw that out. have lots of experience with building race engines. and fixing dumb mistakes

and I hear ya about the valve cover junk, ebay has tons of cheap b series vtec covers, you can purchase some tallstrip2, aircraft stripper in areosal form spray it on, it takes the oe crinkle wrap right off, scuff it up a bit with some sand paper, spray a nice thick primer then your base then your clear when the AN fittings are installed.

LOOKING GOOD! makes me miss my sleeved b20/vtec turbo.
User avatar

By rootbeer_eg
- Fri Feb 01, 2013 11:47 pm #325439 i love this car!!!!!
:woot: :woot: :woot:
cannot wait to see what numbers it puts down
and hear a video of it running



DO WORK!!!!!!
 Reply
Return to Your Ride - Hatchback