B16, B18, B20
User avatar
By mitch6
#299193 I have a few seals leaking, and I pretty much have all the parts I want to replace except for this one cam seal shown in the picture here:

(I believe this is the cam seal correct? right in-between the head and the V-tech solenoid?)

Image

I have read a few forums with people having leaking cam seals similar to mine and buy some USDM B16a2 cam seals as replacement but have then not fitting properly. I know this is a common B series problem and would like to know what other people did when facing this problem for their JDM B16a. If someone has part numbers please let me know!

Thanks for your help in advanced! :thumb:
User avatar
By Eg6H2D
#299204 Out here it's this part #



12513-P72-003

PLUG, CYLINDER HEAD

http://www.hondapartsnow.com/Page_Produ ... d%20(V-TEC)
User avatar
By Eg6H2D
#299205 about it fitting properly stick it in the freezer for a few hours before you install it's just a hard plastic itll contract a bit so you can install easier. they are all the same part number at Honda. it's a p72, meaning it has a Integra GSR part number. So it should fit.

If not you would want to go After market like Golden Eagle or Skunk2

:thumb:
User avatar
By Eg6H2D
#299207 Just pund this out as well you can go to an acura dealer and get one from a Integra GSR from Model year 1993 it brought the B17A1 Engine.


After looking it up it gives a Different part number the a p30 in it which would be in preference to the JDM b16A (P30) which would have been that of the Eg SiR in JApan .

Here's the number for that.
they go for about $5.34USD

12513-P30-000 RUBBER, CYLINDER HEAD SEAL

http://www.acurapartswarehouse.com/Page ... cture=True


Good Luck
User avatar
By mitch6
#299243
EG6b20R wrote:Out here it's this part #



12513-P72-003

PLUG, CYLINDER HEAD

http://www.hondapartsnow.com/Page_Produ ... d%20(V-TEC)


WOW, thanks for all the quick information EG6b20R, I really appreciate it!! I will look in to ordering that soon and will definitely take your advice on freezing the seal before install :thumb:

Thanks again man! Really appreciate it! :D
User avatar
By Eg6H2D
#299268
mitch6 wrote:
EG6b20R wrote:Out here it's this part #



12513-P72-003

PLUG, CYLINDER HEAD

http://www.hondapartsnow.com/Page_Produ ... d%20(V-TEC)


WOW, thanks for all the quick information EG6b20R, I really appreciate it!! I will look in to ordering that soon and will definitely take your advice on freezing the seal before install :thumb:

Thanks again man! Really appreciate it! :D


Your welcome. that's what we are here for. =]

:thumb:
User avatar
By blk92hb
#299328 To be honest it looks like you have an aftermarket cam seal, and if so then all you have to do is get some o-rings.
User avatar
By Eg6H2D
#299417 i thought that crease in the center there was a give away of OEM.
User avatar
By blk92hb
#299537 The oem ones are flat. Her is a link to show the difference.
http://civic-eg.com/viewtopic.php?t=18419
User avatar
By mitch6
#299695
blk92hb wrote:The oem ones are flat. Her is a link to show the difference.
http://civic-eg.com/viewtopic.php?t=18419



Nice, I see the difference!

I bought both the OEM honda one which is flat and I also bout the B17 one which is actually very similar the skunk2 one! Its rubber and is much thicker, looks pretty much identical to my current seal. This is a jdm B16a, not too sure if it should be the same as the 99-00 B16a2 they have here in North America.

I will post some pictures of the two seals later, just waiting for my oem valve cover gasket set to come in now.

Thanks for the link, those pictures helped me out alot!! :thumb: :thumb:
User avatar
By Eg6H2D
#299887
mitch6 wrote:
blk92hb wrote:The oem ones are flat. Her is a link to show the difference.
http://civic-eg.com/viewtopic.php?t=18419



Nice, I see the difference!

I bought both the OEM honda one which is flat and I also bout the B17 one which is actually very similar the skunk2 one! Its rubber and is much thicker, looks pretty much identical to my current seal. This is a jdm B16a, not too sure if it should be the same as the 99-00 B16a2 they have here in North America.

I will post some pictures of the two seals later, just waiting for my oem valve cover gasket set to come in now.

Thanks for the link, those pictures helped me out alot!! :thumb: :thumb:



Niceeee!!! cant wait to see the differences!!
:thumb:
User avatar
By mitch6
#299901 here are some pics of the B17 Cam Seal Plug, looks very similar to the skunk2 one, except its Genuine Honda :thumb: (Sorry bad pics)

The skunk2 one still has bigger O-rings though lol

Image
Image
Image

and here is the OEM one for the B16a2, stolen pic from blk92hb :wink:

Image

I have not changed them yet because I am waiting for my valve cover gasket set to arrive, but hopefully this B17 one will fit nicely
User avatar
By Eg6H2D
#299904
mitch6 wrote:here are some pics of the B17 Cam Seal Plug, looks very similar to the skunk2 one, except its Genuine Honda :thumb: (Sorry bad pics)

The skunk2 one still has bigger O-rings though lol

Image
Image
Image

and here is the OEM one for the B16a2, stolen pic from blk92hb :wink:

Image

I have not changed them yet because I am waiting for my valve cover gasket set to arrive, but hopefully this B17 one will fit nicely



It does resemle the skunk2 one! Nicceeee :thumb: