Civic-EG.com Forum 3.3.1

- Wed Feb 29, 2012 1:44 pm #296604

Great Progress

word!! nice on the Progress man
all i have to say is ///been there did that !
it feels good it is all done and you driving it !!
trust me

90%done


to see my build go here >>> http://civic-eg.com/viewtopic.php?t=8689

- Fri Mar 09, 2012 4:45 am #297541 finally got around to cutting the carbon hood and installing the aerocatches!

just masking off to draw the templates out


cut holes... had to cut the under side verryyy carefully to fit the PW:JDM backing plates i got.


installed! you can also see where i cut out the fog light holes for the IC piping.


opened


flush


UPDATE:
pistons and rods are being media blasted and hot tanked along with the crank, oil pan, oil pickup, and lower baffle are being hot tanked and once thats all back motor assembly can begin


ALSO
planning to order function and form type 1 coil overs and a cometic 5 layer head gasket soon.

eg hatch - jdm B16a

My Build! -> http://www.civic-eg.com/viewtopic.php?t=21567&start=0

- Thu Mar 15, 2012 7:21 pm #298377 got some more work done.
had Dimension Autoworkz soda blast and hot tank some parts.


and got that crank


also got the BYS on, proably gonna need some adjusting but it looks pretty good



also tore into my RSX leathers and found that they were proably layin in a junkyard for awhile at one point or another


and last night i got the water pump and tensioner on the block along with the oil pan studs and the freeze plugs

eg hatch - jdm B16a

My Build! -> http://www.civic-eg.com/viewtopic.php?t=21567&start=0

- Fri Mar 16, 2012 6:51 pm #298488 got my new coil overs last night!

eg hatch - jdm B16a

My Build! -> http://www.civic-eg.com/viewtopic.php?t=21567&start=0

- Mon Mar 19, 2012 3:47 am #298770 Let us know how those coilovers are im debating between those or tein basis

- Mon Mar 19, 2012 4:01 am #298774 BYS

comign along nicely

95 Civic Coupe DX - d15b7 - some mods nothing crazy - My 5th EG
98 Jeep Cherokee 2 door - little lift with 31s 4.0 5 speed
77 Chevrolet C10 - Mild 350/350 combo - lowered a little

- Wed Mar 21, 2012 6:43 pm #299163

Let us know how those coilovers are im debating between those or tein basis

will do for sure !

eg hatch - jdm B16a

My Build! -> http://www.civic-eg.com/viewtopic.php?t=21567&start=0

- Wed Mar 21, 2012 6:43 pm #299164

BYS

comign along nicely

thanks!

eg hatch - jdm B16a

My Build! -> http://www.civic-eg.com/viewtopic.php?t=21567&start=0

- Wed Mar 21, 2012 7:07 pm #299169 got the coiils on



and with the wheel on still in the air...


also got the blox extended ball joints in



on the ground with no motor weight tho

eg hatch - jdm B16a

My Build! -> http://www.civic-eg.com/viewtopic.php?t=21567&start=0

- Mon Mar 26, 2012 5:35 pm #299863 well i got the opportunity to buy a full black interior from a friend parting out his hatch. The dash is in good condition and just needs cleaning up along with every other piece but the door panels are a little rough


blue dash out


interiors


had to cut the black dash so i could put in my cf airbag tray




black dash in




black dash compared to the old blue junk haha

eg hatch - jdm B16a

My Build! -> http://www.civic-eg.com/viewtopic.php?t=21567&start=0

- Tue Mar 27, 2012 1:27 am #299927 Great Build!! lookin fresh

check out the build thread>> http://civic-eg.com/viewtopic.php?p=244809#244809

- Tue Mar 27, 2012 5:54 pm #299996

Great Build!! lookin fresh

thanks!

eg hatch - jdm B16a

My Build! -> http://www.civic-eg.com/viewtopic.php?t=21567&start=0

- Thu Mar 29, 2012 7:52 pm #300318 how long has it been now??? man its coming along great!!!

http://tinyurl.com/Civic-EG-Presidential-Election

Check out my build thread!!!!

- Thu Mar 29, 2012 8:19 pm #300324

how long has it been now??? man its coming along great!!!

Cars been down since the middle of September and I'm.hoping to have it done by the end of April

eg hatch - jdm B16a

My Build! -> http://www.civic-eg.com/viewtopic.php?t=21567&start=0

- Tue May 01, 2012 12:13 am #303418 been awhile since i updated but here is the updates!

finished the interior swap.




also got my supertech valve seals in and my head assembled.




also started to de-loom my engine harness for the minor engine harness tuck.




also painted my water pipe and thermostat housing, got my oem honda head gasket from the local shop Dimension Autoworkz, and decided id go with a new ebay turbo because i sold the t25 i perviously showed.






and a pic of the hatch window


i also have the block basically all assembled i just have to post up the pics.

eg hatch - jdm B16a

My Build! -> http://www.civic-eg.com/viewtopic.php?t=21567&start=0