Civic-EG.com Forum 3.3.1

- Sun Apr 11, 2010 7:32 pm #187025 Do I take it out from the top down or the bottom up I can't het this thing out

- Sun Apr 11, 2010 9:01 pm #187035 from the bottom up and its hard so spray lube and pray

your car is your story, dont let someone else write the book.

91 s10 (sold)
92 civic si with jdm b16a (Sold) http://civic-eg.com/viewtopic.php?t=13460
99 civic lx (current) viewtopic.php?f=63&t=30348

- Sun Apr 11, 2010 9:04 pm #187036 What r u using anyways??? The right way is to use a punch pin...

i pitty the foo who aint got vtec......
EM1 build http://civic-eg.com/viewtopic.php?t=17256

- Sun Apr 11, 2010 10:39 pm #187045 I was using some screw driver bits no success if I buy a 8mm punch will it come out?

- Sun Apr 11, 2010 10:40 pm #187046 N e 1 ever leave it on? I'm just dropping the motor out the bottom

- Sun Apr 11, 2010 11:13 pm #187050 no leaving it in wont work. take a 1/4 deep socket and 3inch extension and hiit it with a hammer. should pop right out.

- Sun Apr 11, 2010 11:26 pm #187054 dnt stop tryin. try somethin new and if it dont work try it again. hence the bitch pen. get the punch set. it was like 6 bucks from home depot.

single slammer = one cam of fury.


si = supercharger inside

[chrono404]

- Mon Apr 12, 2010 12:58 am #187068 Get under the car, take a 6mm punch and a hammer and knock the pin up and it will come out.

Its not as hard as the name implys.

Reference Topics:
http://civic-eg.com/viewtopic.php?t=128 ... =bitch+pin
http://civic-eg.com/viewtopic.php?t=116 ... =bitch+pin

2017 Chevy BoltEV DD |2001 Honda CRV SE

- Mon Apr 12, 2010 1:05 am #187070 6mm or 8mm?

- Mon Apr 12, 2010 4:12 am #187127 wow, i was just wrestiling with one of these with my engine swap today!
i ended up leaving it on the old engine and pulled it out with it still attached!

THEY ARE A BITCH!

My 1995 CX Hatch Build

- Mon Apr 12, 2010 6:12 am #187150 Ha I want to leave it on too but I'm dropping the motor out the bottom

- Mon Apr 12, 2010 6:23 am #187153 Removing the "bitch pin" Without using a hammer

- Mon Apr 12, 2010 12:23 pm #187175 ive never had a problem using a flat punch....

94 Civic Hatch turbo b16 (My weekend warrior)
94 Civic Hatch SOHC VTEC ZC (DD) 33+ MPG

PANDA CREW No.20

- Mon Apr 12, 2010 1:08 pm #187189 yeah thats what i did, removed it form the bottom.
and pulled the engine straight foward out with the linkage still attached.

My 1995 CX Hatch Build

- Tue Apr 13, 2010 12:44 am #187316

Removing the "bitch pin" Without using a hammer

wtf where was this when i needed it

your car is your story, dont let someone else write the book.

91 s10 (sold)
92 civic si with jdm b16a (Sold) http://civic-eg.com/viewtopic.php?t=13460
99 civic lx (current) viewtopic.php?f=63&t=30348