carbon fiber
Posted: Sat May 02, 2009 4:42 amwhats up guy im trying to find a stock looking carbon fiber front bumper if any one knows were i can get one please let me know or make one = \ thanks 
Page 1 of 1
Posted: Sat May 02, 2009 4:42 amPosted: Sat May 02, 2009 5:13 ama carbon fiber full stock looking front bumper? ive never seen that!
Posted: Sat May 02, 2009 2:50 pmNo luck on my serach either.
Get it wrapped in CF
Get it wrapped in CF
Posted: Sat May 02, 2009 4:14 pmI have never seen one before... how ever try this
http://www.realcarbon.com/
These guys know what their doing, they made a carbon fiber drive shaft for my RX-7 to OE Specs with slight modifications (I had them make the shaft to where I could install new u-joints, stock RX7 u joints are one piece with the shaft, so if they go out, you buy a new drive shaft = lame)
Just shoot these guys an email or call them tell em what you want, how you want it and they will pretty much tell you the ball park figure for the cost, I can tell you it WON'T be cheap, carbon fiber is expensive, the only reason most hoods and fenders are not is to the simple fact those companies use molds and just press it and bam....carbon fiber hood for you Honda, to get the best results every inch has to be hand built, good luck! Just do some more research before you decide it could save you some green.
http://www.realcarbon.com/
These guys know what their doing, they made a carbon fiber drive shaft for my RX-7 to OE Specs with slight modifications (I had them make the shaft to where I could install new u-joints, stock RX7 u joints are one piece with the shaft, so if they go out, you buy a new drive shaft = lame)
Just shoot these guys an email or call them tell em what you want, how you want it and they will pretty much tell you the ball park figure for the cost, I can tell you it WON'T be cheap, carbon fiber is expensive, the only reason most hoods and fenders are not is to the simple fact those companies use molds and just press it and bam....carbon fiber hood for you Honda, to get the best results every inch has to be hand built, good luck! Just do some more research before you decide it could save you some green.
Posted: Sun May 03, 2009 7:10 amyou can forget that! "Q. Can you make a car hood, trunk, or motorcycle fender?
A. We cannot make individual car or motorcycle parts as the engineering and tooling required are cost prohibitive. A car hood tool would be around $20,000, to make a class A finish."
A. We cannot make individual car or motorcycle parts as the engineering and tooling required are cost prohibitive. A car hood tool would be around $20,000, to make a class A finish."
Posted: Sun May 03, 2009 7:48 am...I got a shaft they can replicate 
Posted: Sun May 03, 2009 5:16 pm thanks
Posted: Mon May 04, 2009 11:05 pmhey guys thanks i found a guy who think he can do it ill post pics its not going to be completely stock i need room for a big front mount but close ill post pic i still need to get pics of the hatch up hoping to have my motor back soon and start running some high 10s we will see 
Posted: Fri May 15, 2009 12:41 pmhigh 10s??? wow. that'll be really nice numbers. and please, do take pics when the bumper is finished.
Posted: Sat May 16, 2009 2:51 amcmon man wheres this bumper, dieing to see it
Posted: Fri May 22, 2009 6:19 ami know a guy that does cf work too...you can send him anything and he will make a carbon fiber mold of it door panels, handle, toilet seats ext. he did his dash for is s2k full carbon fiber.. www.s2carbonworks.com