ecu help

H22A
 Reply
User avatar

ecu help

By jigga36
- Tue Apr 26, 2011 5:26 pm #252441 i am running a po6 ecu in my h22 swap. does anybody kno what car this is from. i read where ppl say you cant use it b/c it doesnt have vtech but mine kicks in hard at lik 5400 rpms
User avatar

By forcefedEG
- Tue Apr 26, 2011 5:56 pm #252448 Po6 is a stock dx ecu. Unless its been chipped and converted it won't have vtec
User avatar

By jigga36
- Tue Apr 26, 2011 6:30 pm #252453 well i bought the whole swap including the ecu from sombody. does this means they had it chipped?
User avatar

By Eg6H2D
- Tue Apr 26, 2011 8:50 pm #252475 Because it came wityh it doesnt mean its set up for it. Was it running before you bought the engine. It might be chipped to run the motor. or it might now. if it's not then i suggest you find a ECU chipper and get it chipped for the engine or it's not going to run properly..

:thumb:
User avatar

By forcefedEG
- Tue Apr 26, 2011 9:53 pm #252485 Open the ecu its only 5 screws and take a pic put it on here and I can tell you weather it chipped or not :thumb:
User avatar

By mooze
- Wed Apr 27, 2011 5:41 am #252576 if you motor runs with no probs its not a stock p06....ive ran a h22 on a p06....noooooooooooooooooo low end and will throw cel's
User avatar

By forcefedEG
- Thu Apr 28, 2011 2:47 am #252717
mooze wrote:if you motor runs with no probs its not a stock p06....ive ran a h22 on a p06....noooooooooooooooooo low end and will throw cel's



This is verrrrrry true tried running a ls on a po6 barely pulled out of its own way
User avatar

By jigga36
- Thu Apr 28, 2011 10:49 pm #252882 ok my brother is a dumby he told me it was a p06 ecu when in fact it as an p0f srry for the mix up but i read tht this is off an accord SiR does anybody kno anythng else about this ecu lik rev or speed limiter
Image
User avatar

By forcefedEG
- Thu Apr 28, 2011 11:23 pm #252887 I'm not going to bs you thats a jdm ecu and I've never had the cover off of one but it dosent looked chipped to me (I see a 28 pin chip there but Idk if a jdm ecu has something like that factory or not) but if it is it dosent have a data log port, but anyway if its the accord sir ecu it probably will serve you just fine
User avatar

By jigga36
- Thu Apr 28, 2011 11:26 pm #252889 aliright kool 8)
User avatar

By Eg6H2D
- Fri Apr 29, 2011 1:02 am #252903 Yes if it's the Accord Sir Ecu if it's not auto then your good for now..
User avatar

By jigga36
- Fri Apr 29, 2011 1:21 am #252905 thnx for the help
User avatar

By Dirtonaboi
- Mon Jun 13, 2011 7:14 pm #259320 Please forgive me, I'm a noob. I have a P05 ecu, this will not work for an H22 swap ... right?

[img][img]http://i1179.photobucket.com/albums/x398/dirtonaboi/1478d3b5.jpg[/img][/img]
User avatar

By Dirtonaboi
- Tue Jun 14, 2011 5:52 pm #259445 Found this bad boy in the scrap yard today!!!

[img][img]http://i1179.photobucket.com/albums/x398/dirtonaboi/ff08ffa8.jpg[/img][/img]
User avatar

By jigga36
- Tue Jun 21, 2011 7:06 pm #260254 to EG6b20R
i just noticed you said for now... y does somthng go rong
 Reply
Return to H Series